DOC and UVA attenuation with soil aquifer treatment in the saturated zone of an artificial coastal sandfill

Results from a direct recharge experiment conducted in the field to investigate DOC and UVA(254) attenuation rates during the direct injection of UF treated wastewater into a artificial coastal sandfill are presented in this paper. Approximately 500 m(3) of ultra-filtered wastewater was injected into the saturated zone, over a period of 9 days. The movement of the plume was tracked over 80 days, during which time samples were obtained from multilevel samplers installed in transects across the drift axis of the plume. An analysis of fluorescein in the samples obtained during the drift of the UF plume showed that DOC and UVA were attenuated beyond rates predicted by conservative mixing, by up to a maximum of 45%. A degradation coefficient of 0.0175 day(-1) was found to be applicable for DOC degradation. After a drift period of 80 days, DOC and UVA reduced to approximately 4.5 mg/l and 0.100 cm(-1), respectively, from initial values of 8.06 mg/l and 0.199 cm(-1).

Photocatalytic reduction of carbon dioxide into gaseous hydrocarbon using TiO2 pellets

It has been shown that CO₂ could be transformed into hydrocarbons when it is in contact with water vapour and catalysts under UV irradiation. This paper presents an experimental set-up to study the process employing a new approach of heterogeneous photocatalysis using pellet form of catalyst instead of immobilized catalysts on solid substrates. In the experiment, CO₂ mixed with water vapour in saturation state was discharged into a quartz reactor containing porous TiO₂ pellets and illuminated by various UV lamps of different wavelengths for 48 h continuously. The gaseous products extracted were identified using gas chromatography. The results confirmed that CO₂ could be reformed in the presence of water vapour and TiO₂ pellets into CH₄ under continuous UV irradiation at room conditions. It showed that when UVC (253.7 nm) light was used, total yield of methane was approximately 200 ppm which was a fairly good reduction yield as compared to those obtained from the processes using immobilized catalysts through thin-film technique and anchoring method. CO and H₂ were also detected. Switching from UVC to UVA (365 nm) resulted in significant decrease in the product yields. The pellet form of catalyst has been found to be attractive for use in further research on photocatalytic reduction of CO₂.

Year 12 students' mental models of the nature of light

This paper reports on the third year of a three-year longitudinal investigation into six Year 10 secondary students’ understanding of optics at a secondary school level. During the first two years of the study the students’ understanding of geometrical optics was explored with the adoption of constructivist teaching and learning strategies. The students' understanding of geometrical optics following the Year 11 teaching stage then formed the basis of exploration of their mental models of the nature of light. This exploration occurred before, during and following a Year 12 teaching stage where the students studied physical optics and quantum ideas. Before the Year 12 teaching stage the students had constructed mental models of light that related to their understanding of a ray. Over the Year 12 teaching stage the students’ mental models changed to conceptualizations of a photon. There was evidence in the students’ mental models of a hybridization of the particle and wave scientific models. That is, they conceptualized the photon as having both wave and particle characteristics. The variation in the students’ hybrid models also suggested a variation in the way they conceived of the nature of scientific models.

A morphology-related study on photodegradation of protein fibres

The wool fibre has a complex morphology, consisting of an outer layer of cuticle scales surrounding an inner cortex. These two components are hard to separate effectively except by using harsh chemical treatments, making it difficult to determine the susceptibility of the different components of the fibre to photoyellowing. An approach to this problem based on mechanical fibre modification is described. To expose the inner cortex of wool to different degrees, clean wool fibres were converted into ‘powders’ of various fineness via mechanical chopping, air-jet milling, ball milling or their combination. Four types of powdered wool (samples A, B, C and D) were produced with reducing particle size distributions and an increasing level of surface damage as observed using SEM. Sample A contained essentially intact short fibre snippets and sample D contained a large amount of exposed cortical materials. Samples B and C contained a mixture of short fibre snippets and cortical materials. Solid wool discs were then compressed from the corresponding powder samples in a polished stainless steel die to enable colour measurement and UV irradiation studies. ATR-FTIR studies on powder discs demonstrated a small shift in the amide I band from 1644 cm−1 for disc A to 1654 cm−1 for disc D due to the different structures of the wool cuticle and cortex, in agreement with previous studies. Similarly an increase in the intensity ratio of the amide I to amide II band (1540 cm−1) was observed for disc D, which contains a higher fraction of cortical material at the surface of the disc.

Discs prepared from sample D appeared the lightest in colour before exposure and had the slowest photoyellowing rate, whereas discs made from powders A–C with a higher level of cuticle coverage were more yellow before exposure and experienced a faster rate of photoyellowing. This suggests that the yellow chromophores of wool may be more prevalent in cuticle scales, and that wool photoyellowing occurs to a greater extent in the cuticle than in the cortex. Photo-induced chemiluminescence measurements showed that sample D had a higher chemiluminescence intensity after exposure to UVA radiation and a faster decay rate than samples A and B. Thus one of the roles of the wool cuticle may be to protect the cortex by quenching of free radical oxidation during exposure to the UV wavelengths present in sunlight.

The effect of dyes on photo-induced chemiluminescence emission from polymers

Weak photo-induced chemiluminescence (PICL) emission is observed when polymers are exposed to UVA or visible light. The presence of dyes can either increase PICL intensity via Type I photosensitisation which generates polymer free radicals, or reduce it via photo-protection. PICL studies on the eight Blue Wool Standards (BWSs) that are used commercially as lightfastness standards show higher PICL intensity from the least photostable BWSs that use triphenylmethane dyes and lower intensity from more photostable BWSs using UVA and visible wavelengths. The relative PICL intensities do not correlate in a stepwise manner with lightfastness ratings of the BWSs. However dye/polymer combinations that emit high levels of PICL relative to the undyed material are unlikely to have acceptable lightfastness. The xanthene dyes fluorescein and eosin Y are more strongly photosensitising than triphenylmethane dyes on wool and both produce higher PICL emission than undyed wool when irradiated with visible light.

Ultraviolet vision, fluorescence and mate choice in a parrot, the budgerigar Melopsittacus undulatus

As in many parrots, the plumage of the budgerigar Melopsittacus undulatus reflects near-ultraviolet (UVA) wavelengths (300-400 nm) and exhibits UVA-induced fluorescence. However, there have, to our knowledge, been no tests of whether the yellow fluorescence observed under intense UVA illumination has any role in signalling. Four experiments were carried out on wild-type budgerigars, where the presence and absence of UV reflectance and fluorescence were manipulated using filters. Few studies have attempted to separate the contribution of UV reflectance to plumage hue as opposed to brightness or distinguish between a role in sexual as opposed to social preferences. However, our first experiments show that not only do females consistently prefer UV-reflecting males, but also that the observed preferences are due to removal of UV affecting the perceived hue rather than brightness. Furthermore, we found no effect Of the light environment on male response to females, suggesting that the female preferences relate to plumage colour per se. Whilst UV reflectance appears important in heterosexual choice by, females, it has no detectable influence on same-sex association preferences. The results from the second series of experiments suggest that enhancement of the budgerigar's yellow coloration through fluorescence has no effect on male attractiveness. However, the fluorescent plumage may play a role in signalling by virtue of the fact that it absorbs UVA and so increases contrast with nearby UV-reflecting plumage. Our study provides convincing evidence that UV reflectances can play a role in mate choice in non-passerines, but no evidence that the yellow fluorescence observed under UVA illumination is itself important as a signal.

The role of ultraviolet-A reflectance and ultraviolet-A-induced fluorescence in budgerigar mate choice

Many parrots have plumage that either reflects strongly in the ultraviolet-A (UVA) waveband, between 315-400 nm, or exhibits UVA-induced fluorescence. Previous experimental work on budgerigars (Melopsittacus undulatus) suggests that UVA reflectance plays a role in mate choice, as in other diurnal birds, but evidence for fluorescent cues playing a role is unconvincing. Here we report two experiments on budgerigars, designed to determine whether fluorescent cues play a role in signalling when UVA reflectances are absent, an approach which separates removal of UVA reflectance from removal of fluorescence. First, we determined whether the choices of different females are correlated under these treatment conditions. Secondly, we investigated female preferences for fluorescing and non-fluorescing males when UVA reflections are absent, to determine whether the yellow emissions of fluorescence are playing a role in mate choice. Results from experiment 1 do not suggest that females agree on which males are attractive when UVA reflectances are absent, with only half of the subjects choosing the same male. Neither did different females make the same choices in experiment 2. This lack of agreement provides further evidence that UVA reflectances from males play an important role in female choice in this species. Experiment 2 provides no evidence to suggest that UVA-induced fluorescence plays a role in mate choice. Overall, our study supports previous findings showing that UVA reflectance plays a role in sexual signalling in this species, but provides no evidence to suggest the same for fluorescence when UVA reflectances are absent.

The role of ultraviolet-A reflectance and ultraviolet-A induced fluorescence in the appearance of budgerigar plumage: insights from spectrofluorometry and reflectance spectrophotometry

Fluorescence has so far been found in 52 parrot species when illuminated with ultraviolet-A (UVA) 'black' lamps, and two attempts have been made to determine whether such fluorescence plays any role in sexual signalling. However, the contribution of the reflectance versus fluorescence to the total radiance from feathers, even in the most studied species to date (budgerigars), is unclear. Nor has the plumage of this study species been systematically assessed to determine the distribution of fluorescent patches. We therefore used spectrofluorometry to determine which areas of budgerigars fluoresce and the excitation and emission spectra involved; this is the first time that such a technique has been applied to avian plumage. We found that both the yellow crown and (normally hidden) white downy chest feathers exhibit strong UVA-induced fluorescence, with peak emissions at 527 nm and 436 nm, respectively. Conversely, the bright-green chest and dark-blue tail feathers do not fluoresce. When comparing reflectance spectra (400700 nm) from the yellow crown using illuminants with a proportion of UVA comparable to daylight, and illuminants with all UVA removed, no measurable difference resulting from fluorescence was found. This suggests that under normal daylight the contribution of fluorescence to radiance is probably trivial. Furthermore, these spectra revealed that males had fluorescent crowns with substantially higher reflectance than those of females, in both the UV waveband and at longer wavelengths. Reflectance spectrophotometry was also performed on a number of live wild-type male budgerigars to investigate the chromatic contrast between the different plumage areas. This showed that many plumage regions are highly UV-reflective. Overall our results suggest that rapid surveys using UVA black lamps may overestimate the contribution of fluorescence to plumage coloration, and that any signalling role of fluorescence emissions, at least from the yellow crown of budgerigars, may not be as important as previously thought.

A substantially visibly transparent topical physical sunscreen formulation

A topically applied sunscreen composition is provided, which by use of nano-sized particles of a physical UV screening agent in a dermatologically acceptable carrier, provides a dermatologically acceptable level of SPF and broad-spectrum protection from UVA and UVB radiation without the need to include chemical UV screening agents in the composition.

In vitro testing of zinc oxide sunscreens

The UVA performances of two all-mineral zinc oxide sunscreens are measured following Colipa and ISO procedures and compared to a sunscreen containing only organic actives. It is found that the two sunscreen types yield very different in vitro SPF and UVA results. It shown that the results can be rationalized in terms of the differences in the monochromatic extinction spectra of the two types of sunscreens.

Controlled field studies on soil aquifer treatment in a constructed coastal sandfill

A controlled artificial recharge experiment was conducted to investigate the effect of soil aquifer treatment during percolation of secondary and tertiary (ultrafiltered) treated wastewater through the shallow vadoze zone of a newly constructed coastal sandfill. The sandfill is a reclaimed land constructed from marine sand dredged from the seabed. To obtain 1-D flow, a stainless steel column was driven to a depth of 2.5 m, penetrating the phreatic surface. Wastewater was percolated through the column under fully-saturated and unsaturated conditions. Infiltration rates, dissolved organic carbon (DOC) and ultra-violet absorption (UVA) were monitored. The wastewaters were recharged at similar infiltration rates of approximately 5.5 m/day and 3.5 m/day under fully-saturated and unsaturated conditions, respectively. In both cases, clogging occurred 40 days after the start of recharge, under saturated conditions. For secondary treated wastewater, DOC concentration (mg/l) reduced by 28% and 13% under unsaturated and saturated conditions, respectively. The corresponding UVA reduction was 19.4% and 14.1%. Similar reductions in DOC were observed for the tertiary treated wastewater; however, the reduction in UVA was higher; 28% and 22% under unsaturated and saturated conditions, respectively. On an mass removal (mg/m(2) DOC) basis, DOC reduction appeared to be more significant under unsaturated conditions. This is attributed to the presence of interstitial oxygen.

Photostability of wool fabrics coated with pure and modified TiO2 colloids

The surface of wool fabrics was coated with TiO2 and TiO2-based nanocomposite colloids and the impact of this coating on the photostability of wool was investigated. TiO2 along with TiO2/Metal and TiO2/Metal/SiO2 sols were synthesized through a low-temperature sol-gel method and applied to fabrics. Composite colloids were synthesized through integrating the silica and three noble metals of silver (Ag), gold (Au) and platinum (Pt) into the synthesis process of sols. Four different molar ratios of Metal to TiO2 (0.01%, 0.1%, 0.5% and 1%) were used to elucidate the role of metal type and amount on the obtained features. Photostability and UV protection features of fabrics were evaluated through measuring the photo-induced chemiluminescence (PICL), photoyellowing rate and ultraviolet protection factor (UPF) of fabrics. PICL and photoyellowing tests were carried out under UVA and UVC light sources, respectively. PICL profiles demonstrated that the presence of pure and modified TiO2 nanoparticles on fabrics reduced the intensity of PICL peak indicating a lower amount of polymer free radicals in coated wool, compared to that of pristine fabric. Moreover, a higher PICL peak intensity as well as photoyellowing rate was observed on fabrics coated with modified colloids in comparison with pure TiO2. The surface morphology of fabrics was further characterized using FESEM images.

Reprint of: photostability of wool fabrics coated with pure and modified TiO2 colloids

The surface of wool fabrics was coated with TiO2 and TiO2-based nanocomposite colloids and the impact of this coating on the photostability of wool was investigated. TiO2 along with TiO2/Metal and TiO2/Metal/SiO2 sols were synthesized through a low-temperature sol-gel method and applied to fabrics. Composite colloids were synthesized through integrating the silica and three noble metals of silver (Ag), gold (Au) and platinum (Pt) into the synthesis process of sols. Four different molar ratios of Metal to TiO2 (0.01%, 0.1%, 0.5% and 1%) were used to elucidate the role of metal type and amount on the obtained features. Photostability and UV protection features of fabrics were evaluated through measuring the photo-induced chemiluminescence (PICL), photoyellowing rate and ultraviolet protection factor (UPF) of fabrics. PICL and photoyellowing tests were carried out under UVA and UVC light sources, respectively. PICL profiles demonstrated that the presence of pure and modified TiO2 nanoparticles on fabrics reduced the intensity of PICL peak indicating a lower amount of polymer free radicals in coated wool, compared to that of pristine fabric. Moreover, a higher PICL peak intensity as well as photoyellowing rate was observed on fabrics coated with modified colloids in comparison with pure TiO2. The surface morphology of fabrics was further characterized using FESEM images.